Dear sirs,
Many thanks for the IoT SDK.
Just setting up the Raspberry I can't start the Phyton CoAP example as defined in documentation.
The envirinment is:
R...
Hi, I'm testing the beacon example
(ble_app_beacon, Beacon Transmitter Sample Application ) with my custom board.
I use IAR 7.1 for ARM, Softdevice S110 ver 7.1, and...
Hi,
I'm trying out S130 SoftDevice. I have 1 device with S110v7 which acts as a peripheral.
2nd device contains S130 0.9 (I've based my code on S120 multilink central example...
I've gotten the experimental_ble_app_s130_example_c_pca10028 (BLE Dual role application) to work with my nRF51-DK (modified for my needs). It's an nrF51422 chipset.
I want...
Hey I am working on nordic nrf51822 chip ( http://i.imgur.com/q8EM4uq.jpg ).
I want to run a bluenet code which i have forked from github.com/.../bluenet to github.com/....
I am using PCA10031 dongle with SDK 7.2. I tried the blinky example in peripheral directory. Unfortunately it didn't work for me.
When I use the makefile from blank/armgcc...
I've tried compiling and running the ble_app_hrs_rtx demo example suing the makefiles and GCC 'as is'. However, the program just hangs and doesn't do anything. Specifically...
Hello,
I'm working on a BLE application using zephyr and nRF Connect SDK 1.8.0 on the nrf52840. I'm debugging the BLE stack using ozone but whenever I set breakpoints the...
My Current nRF Connect SDK version: 1.5.0
I am trying to follow this reference https://developer.nordicsemi.com/nRF_Connect_SDK/doc/1.5.0/nrf/samples/nrf5340/netboot/README...
I am working on Apple Macbook Air with M1 silicon and I installed nRF command tools version 10.15.4macOS
When I open the toolchain manager , there is an error that shows...
Hi
I'm using the GNSS sample. It gives me an output, but I want to interpret the output of it. How can I read this and translate it to coordinates?
Kind regards
Sarah...
Hi,
I installed nRF Connect SDK (1.9.1) using Toolchain Manager v0.10.3, and nRF Connect for Desktop v3.11.0. Before that I also installed NRF command line tools 10.15.4...
hi,
I want to build and flash only mcumgr bootloader code to my controller , from the example which i observed i am getting that mcumgr is always with some other example...
I use an InsightSIP ISP1907-HT module, I have a 4 layer board to minimise cost. Signals on top and bottom with GND on inside.
I'm concerned that my design could fail emmissions...
Can using whitelist on Central and Peripheral reduce the connection time? In my example I want to advertise every 3secs and want to make sure that the central connects to...
I am completely new to this toolchain and how it works.
I was trying to add a UART sensor to the matter sample project on the nrf52840dk. Is there anyone who can help me...
Hello,
I'm using the flash MX25L1283 together with the NRF52840. I've implemented a new driver for that flash using the nrfx library. Everything works fine !
However,...
Hi,
What's the maximum throughput for nRF52832 as peripheral?
S132 7.1 SDS demonstrates configuration for 192kbps. But I noticed that DLE is not yet enabled. So can...
I want to use the timer to measure the interval between two signals, which requires an accuracy of 1us. But in Timer mode, I don't find a register that can read the current...
Hello Nordic semi team,
I am running into an issue with sd_ble_gattc_read
I have set the MTU size to 70 and I do this:
// Configure the gatt MTU size . memset(&ble_cfg...
Hi,
I'm currently development firmware for a application using a Nordic chip. This application will use some drivers allowing the communication with sensors and for the...
